What does RIMM mean in computer terms?

What does RIMM mean in computer terms?

Rambus inline memory module
While RIMM is commonly believed to stand for “Rambus inline memory module,” Kingston Technology has trademarked “RIMM” and uses only that term. A RIMM module consists of RDRAM chips that are attached using a thin layer of solder, a metal alloy that, when melted, fuses metals to each other.

Is RIMM RAM?

RIMM is computer memory that resembles DIMMs; however, it is 184-pin and is available with built-in ECC support and Non-ECC at speeds up to 800 MHz. RIMM modules are commonly used on the Intel Pentium 4 motherboards. SO-RIMM is a 160-pin module and is Rambus memory used in laptop computers.

What is RDRAM in computer?

RDRAM (Rambus DRAM) is a type of computer device active memory developed and licensed by Rambus Inc. RDRAM competed with synchronous dynamic RAM (SDRAM) during the late 1990s and early 2000s. A bus, or path, connecting RAM to the microprocessor and devices in the computer that used it.

What does dip stand for?

DIP

What does Sodimm stand for?

Small Outline Dual In-line Memory Module
A SODIMM (Small Outline Dual In-line Memory Module) is a memory module with a smaller outline and thickness than standard DIMM modules and designed primarily for notebook computers.

What does DIMM mean in RAM?

dual in-line memory module
A DIMM or dual in-line memory module, commonly called a RAM stick, comprises a series of dynamic random-access memory integrated circuits.

Is RIMM faster than DIMM?

RIMM memory is expensive and slower then DIMMs. RIMM that use 16-bit data bus has 2 notches and 184-pins. RIMM that use a 32-bit data bus has a single notch and 232-pins, it supports dual channels.

What is a full form of RDRAM?

From Wikipedia, the free encyclopedia. Rambus DRAM (RDRAM), and its successors Concurrent Rambus DRAM (CRDRAM) and Direct Rambus DRAM (DRDRAM), are types of synchronous dynamic random-access memory (SDRAM) developed by Rambus from the 1990s through to the early-2000s.

What is a hidden DIP?

A “hidden dip” is the partial disappearance of the road from the driver’s view with reappearance in the extension of the just-passed roadway section (Fig. 1). A particular case of hidden dip appears if there is a curve in the horizontal layout.

What is a DIP switch setting?

(Dual In-line Package switch) A set of tiny toggle switches built into a dual in-line package (DIP), which is mounted directly on a circuit board. The tip of a pen or pencil is used to flip the switch on or off (close or open the circuit).

How is the speed of the rim determined?

Rim speed = How fast the rim is traveling… If the circumference, the distance around the disk, is 36 inches and the angular speed is 1000 rpm, then the rim speed is circumference times RPM, here 36 x 1000 or 36,000 inches per minute. That equals 3,000 feet per minute (divide by 12).

How to find the rim speed of a router?

To find the rim speed, which is usually shown as inches or feet per minute, multiply the diameter of the blade or cutter by PI (3.1416) and multiply that figure by the shaft RPM. 10 x 3.1416 = 31.416 x 5000 = approximately 155, 680 inches per minute. A 1″ diameter router but in the same machine would have an edge speed of 15,560 inches per minute.

What does RIMM stand for in computer category?

RIMM is not an acronym and is a trademark of Rambus incorporated for the Direct RDRAM (Rambus or DRAM) modules. RIMM is computer memory that resembles DIMMs; however, it is 184-pin and is available with built-in ECC support and Non-ECC at speeds up to 800 MHz.

What’s the difference between rim speed and rpm?

RPM and “rim speed” are quite different. RPM refers to the revolutions per minute of the shaft. Most common motors are 1700 or 3400 approximate RPM. A direct drive, ungeared 3400RPM motor will have a 3400 RPM shaft speed.